Can Obd2 Reset Airbag Light?

An airbag light that is on constantly or intermittently can be reset with a few simple steps. First, locate the diagnostic link connector under the dash. It should have 16 pins and will be either blue or black in color.

Once you have found it, use a jumper wire to connect terminals A and B together. Next, turn the key to the ON position without starting the engine and watch for the airbag light to flash. If it does not flash within 30 seconds, remove the jumper wire and repeat the process.

If successful, the light will stay off for approximately six seconds before coming back on again.

If you have an OBD2 reader, you can reset your airbag light easily. All you need to do is connect the reader to your car’s diagnostic port and follow the prompts. Once the light has been reset, it should stay off unless there is another issue with your airbags.


Can Obd Scanner Clear Airbag Light?

When a light on your dash indicates that your airbag system needs service, it can be frustrating. You might be wondering if there’s a way to clear the light without going to the dealership or a mechanic. The simple answer is: no, you cannot clear the airbag light with an OBD scanner.

The reason for this is that the OBD scanner can only read and clear codes for emissions-related problems. The airbag system is not part of the emissions system, so the scanner won’t have any effect on the light. If you’re looking to get your airbag system serviced, you’ll need to take your car to a qualified mechanic or dealer who can diagnose and repair the problem.

Once they’ve fixed the issue, they can reset the light for you. In most cases, simply replacing a faulty sensor will do the trick.

Related:   Can You Swap Pcm from One Car to Another?
So, if you see that dreaded airbag light pop up on your dash, don’t reach for your OBD scanner – head straight to a professional instead!

How Do I Reset My Airbag Light Manually?

If your airbag light is on, it means that there is a problem with the airbag system and it needs to be reset. You can reset the airbag light yourself by following these steps:

1. Disconnect the battery.
This will disable the airbag system so you can work on it without the risk of being injured by an accidental deployment.

2. Locate the fuse box and remove the fuse for the airbag system.

3. Wait 30 seconds for the power to drain from the system.

4. Replace the fuse and reconnect the battery. The airbag light should now be reset and you can test the system to make sure it is working properly before driving again.

Can an Obd Read Airbag Codes?

Yes, an OBD reader can read airbag codes. However, it is important to note that not all OBD readers are created equal. Some OBD readers may only be able to read certain types of airbag codes, while others may be able to read a wider variety of airbag codes.

Additionally, some OBD readers may only be able to read airbag codes from certain manufacturers. Therefore, it is important to consult your specific OBD reader’s documentation to determine its capabilities.

What Scanner Can Read Airbag Codes?

If you’re looking for a scanner that can read airbag codes, the best bet is to find one that’s specifically designed for your vehicle. Every car is different, so it’s important to find a scanner that’s compatible with yours. Once you’ve found the right scanner, follow the instructions to connect it to your car and start reading the codes.

Most scanners will display the code on a screen, along with a description of what the code means. This can be helpful in troubleshooting the issue. If you’re not sure what a particular code means, be sure to consult your car’s manual or an online resource before taking any further action.

Related:   Can You Weld Exhaust With Flux Core

Will Disconnecting Battery Reset Airbag Light

If your car’s airbag light is on, it means that there is a problem with the airbag system and it needs to be serviced. Disconnecting the battery will not reset the airbag light. The only way to reset the airbag light is to have the system repaired by a qualified technician.

How to Reset Airbag Light

If your airbag light is on, it means that there is a problem with your airbag system. The first thing you should do is take your car to a mechanic to have it checked out. If the mechanic finds the airbag system is working properly, they will reset the light for you.

If you need to reset the airbag light yourself, you can do so by disconnecting the battery for about 30 seconds. This will clear any codes that may be stored in the airbag system and turn off the light.

Obd2 Airbag Reset

If your check engine light is on, it’s likely that your car’s onboard diagnostic system (OBD II) has detected a problem. But what does that mean? In order to understand why your check engine light is on, you’ll need to have the code read by an OBD II scanner.

Once the code is read, you can usually reset the light by disconnecting the battery for a few minutes. However, if your check engine light is on because of an airbag issue, you’ll need to take it to a mechanic to have the problem diagnosed and repaired. An airbag reset is not something that can be done at home.

If your car’s OBD II system detects a problem with the airbag deployment system, it will turn on the check engine light and store a trouble code in its memory. The most common codes are B0071 and B0081, which indicate problems with the front passenger or driver’s side airbags, respectively. Other codes may indicate problems with other parts of the airbag system such as the pretensioners or impact sensors.

When you take your car to a mechanic to have the airbag system inspected, they will use an OBD II scanner to read the trouble codes and diagnose the problem. Once they know what’s wrong, they can reset the system so that it’s ready for deployment in case of an accident. It’s important to get any airbag issues fixed as soon as possible because the Deployment of even one Air bag during a crash could save your life!

Related:   Are 243 And 799 Heads the Same?


If your check engine light is on, you can use an OBD2 scanner to reset the airbag light. You will need to connect the scanner to the OBD2 port under the dash and then follow the prompts on the screen. Once the light has been reset, you can drive as normal.

Scroll to Top